DKW Remotes
DKW Remotes
Blog Support & Inquiry
Evo X Ghost
DKW Remotes Shop Evo X Ghost
DKW Remotes
BlogSupport & Inquiry
Scroll

 

The G1 Wireless Welding Hand Remote has clear protective covers for the amber colored screen. Why amber, because at the moment for brightness in lumens, the leds on the board are orange and their wavelength passes through the amber intact.

In this p
Maverick 325x setup heading to Ponoka 👑
Here are my add-on plastics for the EvoR Remote Set for 2026.

I add two pieces on the outside of the enclosure that house 1/2" magnets. And, the inner assembly to mount the pc board. And, the dohicky that braces the antenna from vibration over
Future of the brand. The G1 wireless wireless welding hand remote. I just put the electronics into this housing just now that I received last night in the mail.

It has two half inch round magnets on the back, the popular up5 and dn5 buttons for incr
Did you know I worked on this 3D Model for three months. It's the G1 lower blank. Now, there was interludes waiting for the product to be received. But, lots of late hours and sleeping on the couch nearby.

The goal is to have all the components fit
Went through all the nylon variants and chose this material for the new signature wireless remote ghost line series.

3201PA-F Nylon is my choice. I also looked at PA-12 and PA12-HP. The 3201PA-F is more expensive than the other two but it has the de
Lincoln six pin EvoR remote set with a green faceplate. Oregon bound 🛫
Boxing up this EvoR Wireless Welding Remote Plant Setup heading to Mission, TX 🛫
Got this EvoR Remote Set done tonight for a Trailblazer 325. It's a beauty.
Miller setup heading to Calgary 🛫 Nice orange faceplate
Two Miller units going to Kelowna 🛫 This is my favourite setup to build.
Texas bound plant setup. Currently working on wrapping up all December ordered units.
Plant Setup with two adapters. Has the new G1 charging block which I'm happy about. Has higher voltage and amperage specs than the former to handle the additional requirements. Heading to Port Arthur, TX
Plant setup with four adapters: Miller 14pin, Lincoln 6pin, Lincoln 12pin, Red-d-arc 3pin. Upgraded hand remote with thumb slider attachment. Heading to Crosby TX 🛫
EvoR remote set for a Miller PipePro heading to Ontario. I have 4 plant setups i need to take off my plate then it's business as normal.
Got a remote set done and mailed shortly to Kelowna. My first morning in the office after Xmas. Wasn't easy to get back in the swing of things. But looking forward to picking away at the backlog queue.
Local pickup for a 300D. Rheox remote set with a L14-20P connector. Heading to Saskatchewan
Miller 14pin Evor Remote I finished tonight. It's heading to Kansas 🛫
piceight.jpg
darkevoxlogo.jpg
asd.jpg
6plug.jpg
pic4.jpg
evotwo.jpg
pic6.jpg
pic5.jpg
ranger.jpg
kkkk.jpg
pic7.jpg
stan.jpg
pic12.jpg
pic9.jpg
pic8.jpg
rheoxred2.jpg
cap.jpg
vv.jpg
newwest.jpg
1111.jpg
dddx.jpg
hotstart.jpg
evoxx.jpg
dual.jpg
stiongere.jpg
thumb2.jpg
sa200.png
stingy.jpg
tr1.jpg
theone.jpg
tr2.jpg
hh.jpg
xadapter.jpg
xada.jpg
xcv.jpg
jnunez.jpg
cfr.jpg
poppi.jpg
ws5.jpg
ws3.jpg
ws7.jpg
bw.jpg
tripleremote.jpg
ws6.jpg
remote.jpg
ws11.jpg
ran1ger.jpg
ws9.jpg
pic1.jpg
pic3.jpg
picseven.jpg
picnine.jpg
picsix.jpg
all.jpg
darren1.jpg
picone.jpg
bd1.jpg
330mpx.jpg
New Page
New Gallery
2215434 AB Ltd
29 Rosewood Way,
St. Albert, AB, T8N 8B2,
Canada
7808180313 info@dkwremotes.ca
Hours

Inquiry can forwarded to the email address info@dkwremotes.ca

Photos Courtesy of Poglia  |  Powered by Squarespace